Drainage designed first
Slope to drain, drains and scuppers are sized to the roof area before the membrane is chosen. A low-slope roof that ponds is a roof that leaks.
A flat roof in San Antonio is really a low-slope roof, and it lives or dies on drainage. Flat and low-slope membranes, TPO and modified bitumen, last 15 to 25 years here when the seams hold and the water sheds. When they do not, ponding sits, seams fail from thermal movement and the deck underneath rots. A low-slope install here is drainage first, membrane second.

Low-slope roofs show up on mid-century modern homes, on additions and on flat sections of otherwise pitched homes. The install starts with the deck and the slope to drain: positive drainage is the requirement, because a low-slope roof that holds water will fail at its seams. Then the membrane goes down, TPO or modified bitumen, with heat-welded or sealed seams, edge metal, flashing at every wall and penetration, and drains or scuppers sized to the roof area.
San Antonio's rain makes drainage the design driver. The city averages 32.38 inches of rain a year, with May the wettest month at 4.40 inches, and a single day has delivered 9.52 inches, on 1 July 2002. A low-slope roof that ponds in that kind of rain is a roof that leaks. We size drains and scuppers for the roof area, detail the seams for thermal movement and check the deck for soft spots before the membrane covers them.
A low-slope install is a drainage job with a membrane on top. The items below are standard on our written scope.
Slope to drain, drains and scuppers are sized to the roof area before the membrane is chosen. A low-slope roof that ponds is a roof that leaks.
TPO or modified bitumen installed to the manufacturer's pattern, with seams heat-welded or sealed and checked as they are laid, not after.
Seams fail from thermal movement as the roof expands and contracts in the heat. We detail seams and terminations for that movement.
New edge metal, wall flashing and penetration flashing throughout. Most low-slope leaks start at an edge or a penetration, not in the field.
The deck is inspected before the membrane covers it. Soft or rotted decking is replaced, because a membrane over a bad deck hides the problem.
We prepare the City re-roof paperwork where a permit is needed and the job ends with the City's final building inspection, with the record for your files.
We walk the roof, check the deck from underneath, measure the area and map the drainage: where water goes now, and where it should go.
Slope to drain, drain and scupper placement and sizing are set out on the written scope, so you can see the water path before work starts.
Soft decking is replaced and the surface is prepared. The membrane goes on a sound, dry deck, not over rot.
The membrane is laid to the manufacturer's pattern, seams are welded or sealed and checked, and edge metal and flashing are fitted as the work rises.
We check the drains and seams, confirm water sheds, and walk the finished roof with you, showing the drainage path and the flashing details.
We walk the roof, check the deck from underneath, measure the area and map the drainage: where water goes now, and where it should go.
Welds TPO seams into a single sheet. A welded seam is the strongest joint on a low-slope roof when it is done right.
Rolls each seam as it is laid and probes it after, so a weak seam is found on the day it is made, not in the next rain.
Finds wet decking under an old membrane before the new one covers it, so soft sheets are replaced instead of roofed over.
Cuts membrane and flashing cleanly at edges, penetrations and terminations, where a ragged cut becomes a leak.
Fall protection on every roof, including low-slope ones. A low pitch is still a fall from height.
A sweep of the ground below after the job, because fasteners and membrane offcuts from a low-slope install are a hazard on their own.

A low-slope section that ponds after every heavy rain, with seams opening at the edges, needs drainage fixed before a new membrane goes on.
What we do: redesign the drainage path, replace soft decking, and install a new membrane with heat-welded seams and new edge metal, so water sheds instead of sitting.
Book this service →
An addition with a flat section tied into a pitched roof can leak where the two meet after wind-driven rain.
What we do: re-flash the tie-in, re-grade the drainage on the flat section, and install the membrane with sealed seams and new wall flashing at the joint.
Book this service →
A low-slope garage roof patched more than once, still ponding at the drain with a soft deck underneath, is usually ready for a full install rather than another patch.
What we do: an honest read first, then a full install with the drain re-set, soft deck replaced and a new membrane with welded seams.
Book this service →A flat roof rarely fails in the middle of the field. It fails where water sits, where a seam opens in the heat, where a membrane hides a rotten deck, or where the edge lets water in — and each of those shows up long before the ceiling below ever stains. These are the flat-roof problems we find most, and what they cost if they are left alone.
Ask a pro →Water that sits on a low-slope roof works at the seams until they fail. We design drainage first, so water sheds instead of sitting.
Thermal movement opens seams that were not detailed for it. We weld or seal seams and check them as they are laid.
We inspect the deck before the membrane covers it. A new membrane over a bad deck hides the problem until the deck fails.
Most low-slope leaks start at an edge or a penetration. We fit new edge metal and flashing throughout, not just in the field.
“Found their ad on marketplace, super quick feed back. Gentlemen stopped by same day to inspect roof. This company is extremely professional and quick. They had our roof done in 2 days. Great price point and easy to work with. Thank you Juarez Contracting.”
Alethia VelazquezGoogle review
“Chris was professional, on time for the estimate, very informative about what needed to be done,and willing to work with me. Thank you for a job well done.”
Belinda SalinasGoogle review
“Very fast estimate and fixed within 24 hours of asking them for help. Very fast and very reliable. My roof looks great!”
Jamie KGoogle review
A flat or low-slope membrane in San Antonio realistically lasts 15 to 25 years. It is usually the seams that give out first — thermal movement or ponding water opens them long before the membrane itself wears through. Drainage and seam detailing are what decide the real life.
Both are low-slope membranes. TPO is a single-ply membrane with heat-welded seams and a reflective surface. Modified bitumen is a layered asphalt-based membrane with sealed seams. The right choice depends on the roof's slope, drainage and foot traffic, and we walk through both before you decide.
A roof replaced or installed inside San Antonio city limits needs a City re-roof permit. The flat fee is $28.75, which comes to $31.05 with the City's two 4% surcharges for an online filing. We prepare the paperwork through BuildSA.
Because the drainage is not keeping up with the roof area or the slope to drain is too shallow. San Antonio's heaviest rains, up to 9.52 inches in a day, will find any drainage weakness. We map the water path and re-grade or re-size the drains as part of the install.
Call (254) 329-0299 during business hours for a low-slope inspection with a drainage plan and a written scope.
Call (254) 329-0299 →Call us at (254) 329-0299 or send an email. We answer the phone during business hours and return after-hours messages first thing the next business morning. Low-slope inspections are by appointment.