Stone-coated steel panels
Panels formed into tile profiles and coated with stone granules, installed to the manufacturer's interlocking pattern.
Stone-coated steel is the premium answer to a San Antonio problem: the HOA wants a tile look, the house was not built for tile weight, and the owner is tired of replacing shingles after hail. Steel panels coated in stone granules give the tile appearance at a fraction of tile weight, with steel's hail performance. It is a niche, premium material here, not a common one, and we say so before you decide.

Stone-coated steel panels are steel formed into tile, shake or shingle profiles and coated with stone granules, so the roof reads as tile from the street and performs as steel underneath. Concrete tile weighs 900 to 1,100 pounds per square; stone-coated steel is far lighter, so it suits homes whose structure was not engineered for tile. Steel dents rather than breaking through in hail, and the granule coating gives the texture an HOA palette expects.
The fit is specific. It suits a homeowner in a tile-look HOA who cannot carry tile weight, or a homeowner who wants the tile appearance with steel's hail performance and a longer life than asphalt. It is premium-priced and premium-installed: the panels interlock, the detailing at valleys and walls is its own craft, and a bad detail leaks just as surely as a bad shingle detail. In a historic district, a change to stone-coated steel is a discretionary decision by the Historic and Design Review Commission, not a like-for-like swap.
A stone-coated steel roof is a system, not a surface. The items below are standard on our written scope.
Panels formed into tile profiles and coated with stone granules, installed to the manufacturer's interlocking pattern.
The tile appearance your HOA palette expects, at a fraction of concrete tile's 900 to 1,100 pounds per square, so the structure is not the issue tile would be.
Steel dents rather than breaking through in hail, and we say so when that is what we find. It is the hail trade-off that drives most stone-coated steel decisions.
Walls get step flashing, penetrations get pipe boots, and the perimeter gets new drip edge — all detailed for steel panels, not carried over from a shingle job.
Ridge ventilation paired with soffit intake, sized to the roof area, so the attic does not cook the roof from underneath.
We prepare the City re-roof paperwork where a permit is needed and help you get HOA approval in writing, naming the exact product and colour, before work starts.
We walk the roof, check the deck and structure, and talk through the fit: the tile look, the weight, the hail performance and the premium cost.
Panel profile and colour are set out on the written scope, matched to your HOA palette, so you can see the finished roof before it is ordered.
HOA approval in writing and the City permit paperwork are handled before work starts, so the job is not stopped by a paper that should have been filed first.
Deck prep, underlayment and valley membrane, then panels laid to the interlocking pattern, with flashing fitted at every wall and penetration.
The finished roof is walked with you — panel and flashing details shown — and the final inspection confirmed as scheduled.
We walk the roof, check the deck and structure, and talk through the fit: the tile look, the weight, the hail performance and the premium cost.
Steel panels are cut and folded cleanly where they meet a valley, hip or penetration — a ragged edge there becomes a leak.
Before the steel goes on, the meter finds wet decking — soft sheets are replaced, not roofed over.
Sets straight reference lines for the panel courses. Panels that run true are not cosmetic; they are how you know the roof was laid to spec.
Detail work at flashing and penetrations, where the steel panels meet the waterproofing layer underneath.
Steel panels are slick underfoot, so a steel roof is more dangerous to walk than a shingle roof — and fall protection goes on every pitch.
When the job is done, the lawn and driveway get a sweep — steel offcuts and fasteners left behind are a hazard on their own.

A home in a tile-look HOA whose structure was not engineered for concrete tile's 900 to 1,100 pounds per square needs a lighter way to get the tile look.
What we do: a structural check first, then a stone-coated steel install in a tile profile, with HOA approval in writing naming the exact product and colour.
Book this service →
A home that has replaced shingles after hail may want a roof that dents instead of breaking, with the tile appearance the area expects.
What we do: an honest read on what steel does and does not do in hail, then a stone-coated steel install with new flashing throughout.
Book this service →
A homeowner may want off the 15 to 20 year shingle cycle and onto a longer-lived roof with a tile look.
What we do: a full scope with the premium cost stated plainly, the panel profile matched to the HOA palette, and the install done to the manufacturer's pattern.
Book this service →Stone-coated steel usually enters the conversation when the first choice will not work: a tile look the structure cannot carry, hail that keeps eating shingles, a premium material detailed like shingles, or an HOA palette that bans the look. These are the stone-coated steel problems we see most, and what each one costs when it is chosen without checking the structure, the detailing, or the HOA first.
Ask a pro →Concrete tile weighs 900 to 1,100 pounds per square. Stone-coated steel gives the tile appearance at a fraction of that weight.
Steel dents rather than breaking through. We lay out the hail trade-off plainly, including that denting is cosmetic and the roof still sheds water.
Steel panel detailing is its own craft. We fit flashing and panels for steel, not borrowed from a shingle job, so the details hold.
We match the panel profile and colour to your HOA palette and get approval in writing, naming the exact product and colour, before work starts.
“Found their ad on marketplace, super quick feed back. Gentlemen stopped by same day to inspect roof. This company is extremely professional and quick. They had our roof done in 2 days. Great price point and easy to work with. Thank you Juarez Contracting.”
Alethia VelazquezGoogle review
“Chris was professional, on time for the estimate, very informative about what needed to be done,and willing to work with me. Thank you for a job well done.”
Belinda SalinasGoogle review
“Very fast estimate and fixed within 24 hours of asking them for help. Very fast and very reliable. My roof looks great!”
Jamie KGoogle review
Steel panels formed into tile, shake or shingle profiles and coated with stone granules, so the roof reads as tile from the street and performs as steel underneath.
No, it is a niche, premium material here. Tile and architectural asphalt dominate the city. Stone-coated steel suits a specific fit: a tile-look HOA, a structure not engineered for tile weight, or a homeowner who wants steel's hail performance.
Steel dents rather than breaking through, which is the best hail performance of the common residential materials. Denting is usually cosmetic and the roof still sheds water.
Usually, yes. Stone-coated steel is far lighter than concrete tile, so the structure is not the issue tile would be. It counts as a material change on the City's re-roof application — and in a historic district it is a discretionary decision by the Historic and Design Review Commission.
Call (254) 329-0299 during business hours for a stone-coated steel inspection with a written scope matched to your HOA palette.
Call (254) 329-0299 →Call us at (254) 329-0299 or send an email. We answer the phone during business hours and return after-hours messages first thing the next business morning. Stone-coated steel inspections are by appointment.