A layered asphalt-based membrane for low-slope roofs

Modified bitumen roofing in San Antonio: layered membrane

Modified bitumen is a layered, asphalt-based membrane for low-slope roofs, built up in plies with sealed seams. It suits the flat sections of mid-century modern homes and additions, and it tolerates foot traffic better than a single-ply membrane. Like every low-slope system here, it lives or dies on its seams and its drainage: thermal movement opens seams, ponding finds the weak one, and the deck underneath rots if the leak is not found.

roofer for San Antonio homes
Careful work. Honest options.
About this service

What a modified bitumen roof is in San Antonio

Modified bitumen goes down in layers, with each ply sealed to the one below and the seams sealed and checked as they are laid. The layered build is forgiving of foot traffic and of the odd dropped tool, which is why it suits roofs that get walked on. Flat and low-slope membranes realistically last 15 to 25 years here, and the failure mode is seam failure from thermal movement or ponding, not the membrane wearing through.

Drainage decides the real life. San Antonio averages 32.38 inches of rain a year, with May the wettest month, and a single day has delivered 9.52 inches. A modified bitumen roof that ponds will find its weak seam. We design slope to drain, size drains and scuppers to the roof area, and check every seam as it is laid, so a weak seal is found on the day it is made, not in the next rain.

  • ✓ Layered membrane, sealed seams checked as laid
  • ✓ Tolerates foot traffic better than single-ply
  • ✓ Drainage sized to the roof area
  • ✓ Seams detailed for thermal movement
What's included

What a modified bitumen install includes

A modified bitumen install is a seam job with a membrane on top. The items below are standard on our written scope.

01
✓

Layered membrane

Plies sealed to each other in layers, so a single weak spot does not become a leak path through the whole roof.

02
✓

Seams sealed and checked

Seams are sealed and checked as they are laid, so a weak seal is found on the day it is made, not in the next rain.

03
✓

Drainage designed first

Drains and scuppers are sized to the roof area before the modified bitumen membrane is chosen, for proper slope-to-drain. Ponding is what makes a low-slope roof leak.

04
✓

Foot-traffic tolerance

The layered build tolerates foot traffic better than a single-ply membrane, which suits roofs that get walked on for maintenance.

05
✓

Edge metal and flashing

A modified bitumen install gets new edge metal, wall flashing and penetration flashing throughout. Most low-slope leaks begin at an edge or a penetration, not in the field.

06
✓

Deck checked underneath

The deck is inspected before the modified bitumen goes on; soft or rotted decking is replaced, because a membrane over a bad deck hides the problem.

How it works

What to expect from a modified bitumen install

The modified bitumen install starts with a walk of the roof: deck checked from underneath, area measured, drainage mapped — where the water goes now, and where it should go.

Before work starts, the written modified bitumen scope shows the water path: the slope-to-drain design, and the placement and sizing of every drain and scupper.

The surface is prepared and any soft decking replaced first, so the modified bitumen membrane goes onto a sound, dry deck — never over rot.

Plies are laid and sealed to the manufacturer's pattern, seams are checked as they are laid, and edge metal and flashing are fitted.

With the modified bitumen down, drains and seams are checked, water shedding confirmed, and the finished roof walked with you — drainage path and flashing details shown.

Roof Replacement
STEP 01Inspection and measurements

We walk the roof, check the deck from underneath, measure the area and map the drainage for the modified bitumen install: where water goes now, and where it should go.

Tools & methods

Tools and methods we bring to the job

01
✓

Torch or adhesive applicator

Bonds modified bitumen plies and seams to the manufacturer's method, so the layers become one membrane.

02
✓

Seam roller and probe

Rolls each modified bitumen seam as it is laid and probes it after, so a weak seam is found on the day it is made, not in the next rain.

03
✓

Moisture meter

Under the old modified bitumen membrane, the meter finds wet decking before the new one covers it — soft sheets are replaced, not roofed over.

04
✓

Roofing knife and straight edge

Cuts modified bitumen and flashing cleanly at edges, penetrations and terminations, where a ragged cut becomes a leak.

05
✓

Fall protection harness

Fall protection on every roof, including low-slope ones. A low pitch is still a fall from height, and a granulated cap sheet is no safer to walk than any other membrane.

06
✓

Magnetic sweeper

The ground below gets a sweep when the job is done: fasteners and membrane offcuts left lying around are a hazard on their own.

Recent work

What the work looks like.

Low-slope section ponding after rain
Modified Bitumen Roofing

Low-slope section ponding after rain

A low-slope modified bitumen section can pond after every heavy rain, with seams opening at the edges where the water stands.

What we do: the drainage path is redesigned, soft decking replaced, and modified bitumen installed with sealed seams and new edge metal — so water sheds rather than sitting.

Book this service →
Flat section tied into a pitched roof
Modified Bitumen Roofing

Flat section tied into a pitched roof

An addition with a flat modified bitumen section tied into a pitched roof can leak where the two meet in wind-driven rain.

What we do: the tie-in is re-flashed, drainage on the flat section re-graded, and modified bitumen fitted with sealed seams and new wall flashing at the joint.

Book this service →
Modified Bitumen Roofing

Garage roof that gets walked on

A garage roof that gets walked on for maintenance needs a membrane that tolerates foot traffic — a single-ply membrane can puncture under it.

What we do: an honest read on membrane choice, then a layered modified bitumen install that tolerates foot traffic, with the drain re-set and soft deck replaced.

Book this service →
Problems we solve

Roof problems we solve before they spread

Most low-slope failures in San Antonio announce themselves long before the ceiling stains: blisters in the cap sheet, seams lifting in the heat, ponding at the drains. These are the modified bitumen failures we see most often, and what happens when they are left alone.

Ask a pro →
01

Seams opening in the heat

Seams that were not detailed for thermal movement open up as the roof moves. We seal each seam and check it as it is laid, so a weak seal is caught the same day.

↗
02

Ponding that never dries

On a modified bitumen install, drainage comes first: standing water works at the seams until they fail, and the roof must shed water instead of holding it.

↗
03

A membrane over a rotten deck

Before the modified bitumen membrane goes on, the deck is inspected — a new membrane over a bad deck hides the problem until the deck fails.

↗
04

Punctures from foot traffic

A single-ply membrane punctures easily underfoot. The layered modified bitumen build tolerates traffic better, and we say so when that is the deciding factor.

↗
Proof you can check

Credentials and reviews

  • 4.8 stars from 19 Google reviews · Roofing contractor, San Antonio, TX
  • 14526 Jones Maltsberger Rd Ste 210, San Antonio, TX 78247
  • Phone (254) 329-0299 · bestjuarezcontracting.com
  • Mon–Tue & Thu–Fri 8 AM–6 PM · Wed 8 AM–6:30 PM · Sat 8 AM–12 PM · Sun closed
Customer reviews

What San Antonio homeowners say

★★★★★
“Found their ad on marketplace, super quick feed back. Gentlemen stopped by same day to inspect roof. This company is extremely professional and quick. They had our roof done in 2 days. Great price point and easy to work with. Thank you Juarez Contracting.”
AV

Alethia VelazquezGoogle review

★★★★★
“Very fast estimate and fixed within 24 hours of asking them for help. Very fast and very reliable. My roof looks great!”
JK

Jamie KGoogle review

Good questions

Modified Bitumen Roofing questions we hear every week

(254) 329-0299 →

For a modified bitumen membrane in San Antonio, 15 to 25 years is the realistic range. When one fails early it is usually the seams giving way to thermal movement or to ponding water, rather than the membrane itself wearing through.

They are different systems for the same job. Modified bitumen is a layered asphalt-based membrane with sealed seams and better foot-traffic tolerance. TPO is a single-ply membrane with heat-welded seams and a reflective surface. The right choice depends on slope, drainage and foot traffic.

A modified bitumen roof replaced or installed inside San Antonio city limits needs a City re-roof permit. The flat fee is $28.75, which comes to $31.05 with the City’s two 4% surcharges for an online filing. We prepare the paperwork through BuildSA.

Because the drainage is not keeping up with the roof area or the slope to drain is too shallow. We map the water path and fix the drainage as part of the install, not just the membrane.

07Roofing in Monte VistaMonte Vista roofing, read on its own build era, material and storm exposure.↗08Roofing in Beacon HillBeacon Hill roofing, read on its own build era, material and storm exposure.↗
Ready when you are

Get your modified bitumen roof installed properly

Call (254) 329-0299 during business hours for a low-slope inspection with a drainage plan and a written scope.

Call (254) 329-0299 →
Request an appointment

Get Your Roof Inspected

Call us at (254) 329-0299 or send an email. We answer the phone during business hours and return after-hours messages first thing the next business morning. Modified bitumen inspections are by appointment.

Call during business hours(254) 329-0299Email the office[email protected]
Office hoursMon–Tue & Thu–Fri 8 AM–6 PM · Wed 8 AM–6:30 PM · Sat 8 AM–12 PM · Sun closed
Request received — our team will be in touch shortly.
↗
Questions?Call now